The Aliens Legacy
http://www.forum.alienslegacy.com/

G&P TM pulse rifle WIP update Oct 19 last post
http://www.forum.alienslegacy.com/viewtopic.php?f=4&t=13740		 Page 1 of 1
Author:  Drake07046139 [ Mon Oct 14, 2013 11:19 pm ]
Post subject:  G&P TM pulse rifle WIP update Oct 19 last post
Hi what does eveyone use for the battery in the their own pulse rifle, I have one but the battery is so old from the previou user that it never holds charge anymore.

Its located at the front on mine, and in all honesty I havent done a whole lot of research on this and on differnt methods to remove the battery.
If anyone knows the process to get to that part of the gun without damaging anything please let me know.

Thanks in advance
Author:  robiwon [ Tue Oct 15, 2013 2:33 am ]
Post subject:  Re: G&P TM pulse rifle battery question.
Check the first link in my signature below. :D
Author:  Drake07046139 [ Tue Oct 15, 2013 5:07 am ]
Post subject: 
thanks robiwon, is in all honesty im scared shitless to open it incase I break it haha
Author:  robiwon [ Tue Oct 15, 2013 10:53 am ]
Post subject:  Re: G&P TM pulse rifle battery question.
You can do it, if you want to. The hard part is separating the shrouds. Go slow, a little at a time, prying open with a flat blade screwdriver. You may bend the plastic here or there, but you wont "break" it. It is not for the faint of heart though. Proceed at your own risk.
Author:  king_p90 [ Tue Oct 15, 2013 11:07 am ]
Post subject: 
I found the best tool to separate the shrouds was a pallet knife, managed to get them apart without a scratch.

Have a look at some build photos, this will tell you where all the pegs and roll pins are (pvb has a build log on his website http://www.medwaypvb.pwp.blueyonder.co.uk/pulse7.html).
Author:  Drake07046139 [ Thu Oct 17, 2013 2:24 am ]
Post subject: 
Thanks for the help gentlemen :)

I have taken the plunge and I have taken the rifle apart.

1st thing I am going to do is repaint parts, I dont like the greyish cage for the spas and the barrel "guard"?
2nd replace the crappy shotgun shell with a resin spat frag shell that I have
3rd replace the craptastic battery that was inside it from the previous owner
4th tidy up minor problems that I have noticed.

So far I have the rifle apart and I have repainted the shell entry point under the spas cage and added the spat frag shell.

I have noticed my frag shell sits quite far in the cage but looking down the shroud its centered so I dont know if I will move it closer on leave it as is, any ideas marines?


Image
IMG_6888 by scottdickson1, on Flickr

Image
IMG_6887 by scottdickson1, on Flickr

Image
IMG_6886 by scottdickson1, on Flickr

Image
IMG_6885 by scottdickson1, on Flickr

Resprayed the spas cage from the greyish black to matt black (weathering will be added in due course)

Image
IMG_6906 by scottdickson1, on Flickr

I think it looks far better now

Image
IMG_6911 by scottdickson1, on Flickr

Image
IMG_6912 by scottdickson1, on Flickr
Author:  robiwon [ Thu Oct 17, 2013 10:48 am ]
Post subject:  Re: G&P TM pulse rifle WIP and battery replacement
Congrats on taking apart your PR. Now that wasn't so bad was it? You did get rid of those pesky roll pins right?

If you move your grenade closer to the ejection port just make sure the metal tube will still slide over it when you "rack" your grenade launcher. Otherwise it looks fine to me.

Looking forward to more updates!
Author:  Drake07046139 [ Thu Oct 17, 2013 4:59 pm ]
Post subject: 
When I was taking it apart I was nervous to say the least, and Iv been an airsoft gun tech for a few years now, so I know pressure. But I'm happy it's apart and I'm starting to make it a bit better
Author:  Drake07046139 [ Sat Oct 19, 2013 2:40 pm ]
Post subject: 
new update

Did a little weathering technique Iv used before on the spas cage to bring out a gun metal look to it, just put it together so i can get a rough idea on how it will look finished

Image
IMG_6917 by scottdickson1, on Flickr

Image
IMG_6918 by scottdickson1, on Flickr

Image
IMG_6921 by scottdickson1, on Flickr

im pleased so far with the progress. would like to hear anyone's opinion on it though and im looking to possibly get one of nobles mag base's anyone have one that they care to inform me on the do's and dont's regarding them

thanks for looking and any advise in advance
Author:  blackbeltjonzey [ Tue Oct 22, 2013 1:31 pm ]
Post subject:  Re: G&P TM pulse rifle WIP update Oct 19 last post
Any idea where i can get one? In the UK, (M40 grenade) I was gunna make one but this looks cool...


(2 replace the crappy shotgun shell with a resin spat frag shell that I have)
Author:  88reaper88 [ Tue Oct 22, 2013 1:44 pm ]
Post subject: 
Sucks
Author:  Drake07046139 [ Tue Oct 22, 2013 3:31 pm ]
Post subject: 
Blackbeltjonzey, im sorry buddy I got mine from spat a while back and Simon I know who you are. I know what you want. If you are looking for ransom, I can tell you I don't have money. But what I do have are a very particular set of skills; skills I have acquired over a very long career. Skills that make me a nightmare for people like you. If you take back your sucks comment , that'll be the end of it. I will not look for you, I will not pursue you. But if you don't, I will look for you, I will find you, and I will kill you :P

Cheers simon I know you meant to say its a decent job haha
Author:  blackbeltjonzey [ Wed Oct 23, 2013 11:11 am ]
Post subject:  Re: G&P TM pulse rifle WIP update Oct 19 last post
Ok. man, I'll try and make one that looks half decent. Its a nightmare to get stuff over here... :(
Author:  robiwon [ Wed Oct 23, 2013 2:12 pm ]
Post subject:  Re: G&P TM pulse rifle WIP update Oct 19 last post
I may have some red caps. Let me check. Not sure if they are right ones or the correct size. Stand by...
Author:  Drake07046139 [ Wed Oct 23, 2013 2:37 pm ]
Post subject: 
ask in the px blackbelt somebody may have one spare
Page 1 of 1 All times are UTC [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/