dont know if any1 else has this problem but my mag(190) is extremely hard to remove when its in me PR. any ideas on how to make it so it comes out easier(lube etc).

_________________
Cpl. Rick "Dangerous" Butler
A04/TQ2.0.62158E1
UKCM
______________________


"All right. Now listen up! I want this thing to go smooth and by the numbers. I want DCS and tactical database assimilation by Oh-Eight-Thirty. Ordinance loading, weapons strip, and dropship prep details will have seven hours! Now move it people!"

The mag in mine was fine until I built the PR with shroud around the TM Thompson, then it would get stuck and had to be removed with a screwdriver.

I ended up giving it to a metalwork firm to grind/file the sides of the mag down by about half a mm, now it fits fine.

_________________
Steve
Corporal in 69th Regt. 1st Batt. Homer’s Heroes.

"I'd like to die at the age of 80 in my own bed, with a belly full of wine and a girl's mouth around my c**k."

ok pvb ill do that. oh and i used your step by step guide to build my PR so thx for making that.

_________________
Cpl. Rick "Dangerous" Butler
A04/TQ2.0.62158E1
UKCM
______________________


"All right. Now listen up! I want this thing to go smooth and by the numbers. I want DCS and tactical database assimilation by Oh-Eight-Thirty. Ordinance loading, weapons strip, and dropship prep details will have seven hours! Now move it people!"

Marker pen? *shakes head*

Never had that problem.

There are two spacer pieces inside the magwell.

One covers the counter electronics, the other

helps fill in the other side to allow smooth mag

insertion. My guess is the one side is not firmly

screwed down.

Post some picts of the inside of your magwell.

You should not have file down your mags.

everything is screwed down tight. ill have a look inside the magwell an see if i can spot anything that might be sticking out.
thx

_________________
Cpl. Rick "Dangerous" Butler
A04/TQ2.0.62158E1
UKCM
______________________


"All right. Now listen up! I want this thing to go smooth and by the numbers. I want DCS and tactical database assimilation by Oh-Eight-Thirty. Ordinance loading, weapons strip, and dropship prep details will have seven hours! Now move it people!"

I had no problems like that also.

I found that it was abit loose and did not hit the micro switch so I put some black tape down the sides of the magazine and also bent the micro switch abit.

Filing down the magazine is a bit over kill.

It could be that the two plates on the mag well need to be loosen off so the magazine is nice and free. The G&P is squeezed together too much and that why the magazine is tight. Just undo the screws on one side of the G&P kit and try to get the gap equal all the way round the kit. That should be the ticket.

Cheer's Steven

Tried all that, but could not get the whole shroud apart due to a couple of the hex bolts losing their hex head shape, so the key just turned inside the hole.

Mine wasn't just a liitle tight, as I said the mag actually got stuck fast, so I had to hit a screwdriver against the end of the mag to get it free.

Anyway, mine's fixed now.

_________________
Steve
Corporal in 69th Regt. 1st Batt. Homer’s Heroes.

"I'd like to die at the age of 80 in my own bed, with a belly full of wine and a girl's mouth around my c**k."

1. The mag is out of sight inside the PR.

2. The PR is mainly for display purposes, so I'm not after a 'posh' look to the thing.

_________________
Steve
Corporal in 69th Regt. 1st Batt. Homer’s Heroes.

"I'd like to die at the age of 80 in my own bed, with a belly full of wine and a girl's mouth around my c**k."

If you're using the Marui Thompson, just take a common household metal file, and file SLIGHTLY about 2" of length at the top of the bit on the back of the magazine that fits into the Thompson receiver. I did that to all my Thompson mags and they come out just fine when the release lever is moved. They don't drop free, but they are MUCH easier to remove. The key is to file a little, test it, then file more if needed.

Russ

_________________
"A writer needs a pen, a painter a brush, and a filmmaker an army." - Orson Wells.

http://www.rookscastle.com
http://www.alchemyarms.com

ok filing will commence 2day. should be ok afterwards.
ill let u guys know if all goes well....hopefully.

_________________
Cpl. Rick "Dangerous" Butler
A04/TQ2.0.62158E1
UKCM
______________________


"All right. Now listen up! I want this thing to go smooth and by the numbers. I want DCS and tactical database assimilation by Oh-Eight-Thirty. Ordinance loading, weapons strip, and dropship prep details will have seven hours! Now move it people!"

Mine was sticking at all the points that got filed.

TBH, the short mag was probably just made slightly too wide/deep, as the longer mag had less trouble.

_________________
Steve
Corporal in 69th Regt. 1st Batt. Homer’s Heroes.

"I'd like to die at the age of 80 in my own bed, with a belly full of wine and a girl's mouth around my c**k."

Marker pen.

I'm sad. Sad in my heart that work of other marines have not provided an example for you.



There are so many better ways to fix that, because eventually, somewhere, someone will see it.

For shame.



Plus, the scratches probably looked better than the marker pen does now.

Weathering can give a PR real character.



Even if it's hidden on display, you posted pictures of it on the internet.



I'm sad in my heart marines. SAD.



I'm just busting your balls. If you want to have marker on your magazine, you go right ahead!

i havent used a marker pen to cover up the scratch marks.
1. it doesnt look too bad
2. cant be bothered

gets in and out ok now, if its a lil tight then a quick tap gets it out.

_________________
Cpl. Rick "Dangerous" Butler
A04/TQ2.0.62158E1
UKCM
______________________


"All right. Now listen up! I want this thing to go smooth and by the numbers. I want DCS and tactical database assimilation by Oh-Eight-Thirty. Ordinance loading, weapons strip, and dropship prep details will have seven hours! Now move it people!"

Bought a can of satin black spary paint in Homebase today, just so I could do this:



Happy now?

_________________
Steve
Corporal in 69th Regt. 1st Batt. Homer’s Heroes.

"I'd like to die at the age of 80 in my own bed, with a belly full of wine and a girl's mouth around my c**k."

good job PVB, now it dont look like its been touched.
although it didnt look too bad b4 u sprayed it, an like u said its covered up anyway.

_________________
Cpl. Rick "Dangerous" Butler
A04/TQ2.0.62158E1
UKCM
______________________


"All right. Now listen up! I want this thing to go smooth and by the numbers. I want DCS and tactical database assimilation by Oh-Eight-Thirty. Ordinance loading, weapons strip, and dropship prep details will have seven hours! Now move it people!"

The flash made the marker pen look a lot worse than it was, but at least I've stopped some on here feeling sad.

_________________
Steve
Corporal in 69th Regt. 1st Batt. Homer’s Heroes.

"I'd like to die at the age of 80 in my own bed, with a belly full of wine and a girl's mouth around my c**k."